Parker - KITS




Please wait. Catalogs are being retrieved...

KITS

KITS

Parker electrical connection kits are universal all-in-one connection kits for making the electrical connections (input power, splice, input power splice, and termination) for Parker electric trace tubing bundles.

 End Seal Boot (ESB) Kit  Splice Kit SK-612

Parker end seal boot (ESB) kits are designed to prevent moisture from entering the ends of Parker Temptrace® bundles. Each boot allows up to three tube breakouts. These breakouts have marks to specify where to cut for either a 1/4", 3/8" and 1/2" tube.

Kit contains:
(2) End Seal Boots
(6) Stainless Steel Hose Clamps
(2) Plastic Hose Clamps (1.47" - 1.72")
(2) Plastic Hose Clamps (1.73"-2.02")
(2) Mastic Sealant (3/4" wide x 9" long)

The SK-612 has been designed to provide long life, weatherproof thermal insulation and jacket over a tube fitting or instrument connection. 

There is sufficient material in each SK-612 Splice Kit to insulate two (2) splices or bundle ends.

Kit contains:
(1) Roll waterproof sealing tape.
(2) 8"x 8" self-sealing rubber sheets
with a 6" x 12" fiberglass pad.

 Splice Kit SK-630  Splice Kit SK-696

The SK-630 has been designed to provide long life, weatherproof thermal insulation and jacket over a tube fitting or instrument connection.  There is sufficient material in each SK-612 Splice Kit to insulate two (2) splices or bundle ends.

Kit contains:
(1) Roll waterproof sealing tape.
(2) 8"x 30" self-sealing rubber sheets w/ a 6" x 30" fiberglass pad.

The SK-696 has been designed to provide long life, weatherproof thermal insulation and jacket for longer lengths up to 96" (8ft.) of bundles or multiple connections.

Kit contains:
(1) Roll 8"x 96" self-sealing rubber sheet.
(1) Roll 6" x 96" fiberglass pad.
(1) Roll waterproof sealing tape.

 

4041-2101 Temptrace Electric Power 4041-8200 Electrical End

4041-2101 Temptrace Power Connection Kit with Junction Box
4041-2101 Temptrace Electric Power Connection Kit for SL & SH Series - Self-Regulating Bundles

Kit contains:
(1) Molded junction box consisting of: Base-Box-Lid-Hardware
(4) Heater grommets (grommet used based upon heater type)
(1) Pipe strap 1" – 3-1/2"
(1) RTV-103BLK
(1)Three position terminal block
(1)Mounting screw for terminal block
(1) Caution label

4041-8200 Electrical End Termination Kit for SL & SH Self-Regulating Bundles

Parker electrical end termination kit (4041-8200) is designed to provide a method of terminating the non-powered end of the heating cable.

Kit contains:
(2) Molded end terminations
(2) Screws
(1) Sealing grommet
(1) Caution label
(1)Roll glass tape
(1)Additional heat grommets

4041-5300 Temptrace Universal Kit 4031-0001 Electrical Connection Kit

4041-5300 Temptrace Universal Kit for Self-Regulating Bundles
4041-5300 Temptrace Electric Splice or Tee Connection Kit for SL & SH Series - Self-Regulating Bundles

An easily installed combination power splice and tee for Self-Regulating Bundle.

Caution: The heater will come in contact with the power feed wires in the junction box. Make sure that the temperature rating of the power feed wire insulation is adequate for the heater used.

Kit contains:
(1) 3/4” Pipe Stand
(3) Ring Terminals
(1) Sealing Grommet
(2) Cable Entry Fittings
(4) Stainless Steel Pipe Straps  - (2-large, 2-small)
(1) 3/4” Pipe Plug
(1) Grounding Screw
(1) 3 Hub Box
(2) RTV-103BLK
(1) Box Cover
(1) SS Label
(6) Wire Nuts
(2) Reducing Bushings
(2) Butt Splice Connectors
(3) 1” Heat Shrink Tubes
(1) SK-612 (Seal Patch Kit)
(3) 3” Heat Shrink Tubes
(3) 10” Heat Shrink Sleeves

4031-0001 Electrical Connection Kit for CL & CH Series Constant Wattage Temptrace

Parker electrical connection kits are universal all-in-one connection kits for making the electrical connections (input power, splice, input power splice, and termination) for Parker electric trace tubing bundles. The kits contain all the necessary components and hardware to make one input connection, one splice connection or one input power splice connection as well as two termination connections. The connection kits are designed for use in ordinary locations and Class I, Division 2, Groups B, C, and D; Class II, Division 2, Groups F and G; Class III, Divisions 1 and 2 hazardous locations.

Kit contains:
(1) Connection Box
(1) Connection Box Gasket
(1) Connection Box Cover
(1) Mounting Bracket
(1) 3/4" Locknut
(1) 3/4" Pipe Plug
(1) "Electric Trace" caution sticker
(1) 2.8 oz Black RTV Sealant
(1) Bracket Assembly
(2) Connector unions
(2) Heating cable grommets
(2) Plastic cable ties
(2) Non-insulated butt splice (12-10 AWG)
(3) Non-insulated butt splice (16-14 AWG)
(2) Heater termination boots
(1) Roll 3/4" wide temperature tape

4041-6101 Electrical End Termination  

4041-6101 Electrical End Termination Kit for Self-Regulating Bundles

Parker electrical end termination kit (4041-6101) is designed to provide a
method of terminating the non-powered end of the heating cable.

4041-6101 Use with Single Tube Bundle
4041-6102 Use with Two Tube Bundle
4041-6103 Use with Three Tube Bundle
4041-6104 Use with Four Tube Bundle

Kit contains:
(1) Heatshrink boot
(1) Fluoropolymer heat shrink sleeve